SLT-1 Sear Link Technology Trigger

KE Arms is pleased to announce the release of the SLT-1 Sear Link Technology Trigger.ps_IMG_2049

KE Arms has licensed the manufacturing and distribution rights for the patent pending Sear Link Technology trigger system from M&M Manufacturing.  All components are made and assembled in the USA.

ps_IMG_2048

The SLT-1 has been tested thoroughly before release with tens of thousands of rounds in traditional 5.56 AR platforms, .308 AR platforms, 9mm AR pattern blow back carbines, and the SIG MPX

ps_IMG_2052

TRIGGER FEATURES

-4.5 POUND TRIGGER PULL
– MINIMAL TAKEUP AND OVERTRAVEL
– ULTRA-CRISP BREAK
– DRASTICALLY REDUCED SPLIT TIMES
– SIMPLE DROP IN INSTALLATION

EFFICIENT ENERGY TRANSFER

– There is no disconnector for the hammer to drive through, thus creating a more efficient cycle of the bolt simply pushing the hammer out of the way as the gun fires.
– Forces of the bolt on the hammer are not transmitted into any other components of the trigger assembly.
– Constant sear engagement against the hammer means the trigger is always ready to reset and fire

ps_IMG_2054

IMPROVED RELIABILITY
Moving parts are sealed in the underside of the housing making it less susceptible to fouling and debris.

ps_IMG_2053

IMPROVED LONGEVITY
No impact on moving internal parts increases longevity of the trigger system.

INSTALLATION 
The SLT-1 Drops into mil-spec fire control pockets and is retained with standard fire control pins captured by springs inside the housing bushings.

IMPROVED SAFETY
Due to the unique geometry of the trigger, the safety can always be applied regardless of the hammer being down or cocked. When used appropriately this adds another level of safety to administrative handling and clearing of malfunctions.

Ambi Selector Included for a Limited Time
For a limited time KE Arms Ambi-Selectors will be included with all orders direct from KE Arms. If you purchase an SLT-1 from an authorized retailer during this time, you will receive a voucher for a free ambi-selector in the package.

Introductory MSRP of $199.95
Order online at http://www.kearms.com/slt-1-sear-link-technology-trigger.aspx

For Sales inquiries e-mail sales@kearms.com
For Media inquiries e-mail Russell@kearms.com

KE-9 80% Glock Mag Lowers

ps_IMG_0613

The KE-9 Billet lower receiver is precision machined in-house from hi-grade 7075 billet master plate to milspec standards making it compatible with most milspec 9mm uppers. Features a broached mag well and milspec 8625 type III, class 2 hard anodized. All that is left to do is machine the fire control pocket, for the trigger group and drill a few holes. Once complete you will have a fully functional KE-15 type lower.

The KE-9 accepts Glock OEM and after market Glock style magazines. The magazine catch is included and is machined from aluminum billet and hard coat anodized. The ejector is included and is secured with 2 set screws. The bolt catch hole is threaded and and screw for installation is included.

– This is not a completed receiver and still requires machining to be done in order to have an operational firearm.

– NO FFL is required for purchase, item can be shipped directly to your home.

– As determined by the firearms technology branch of the ATF, this lower receiver is not classified as a “firearm” as defined by the GCA of 1968.

ps_IMG_1673

KE-9 9mm Glock Magazine Lower

KE Arms is pleased to announce our billet KE-9 Glock Magazine Compatible lowers! 

ps_IMG_0576

The KE-9 Billet lower receiver is precision machined in-house from hi-grade 7075 billet master plate to milspec standards making it compatible with most milspec 9mm uppers. Features a broached mag well and milspec 8625 type III, class 2 hard anodized. Ready to be assembled with your choice of lower parts kit.

The KE-9 accepts Glock OEM and aftermarket Glock style magazines. The magazine catch is included and is machined from aluminum billet and hard coat anodized. The ejector is included and is secured with 2 set screws. The bolt catch hole is threaded and and screw for installation is included.

The KE-9 is compatible with most 9mm uppers with mil-spec spacing between the take down pin lugs and 9mm bolts machined to clear through Glock magazine feed lips.  Last round bolt hold open is dependent upon the upper used.

MSRP $199.95

ps_IMG_0593

ps_IMG_1651

This lower comes assembled with our Mil-Spec Lower Parts Kit. The magazine catch is machined from billet and hard anodized. Our 5.5oz heavy 9mm buffer is installed. Mount the upper of your choice with bolt carrier group that clears through glock feed ramps, and this unit is ready to go!

MSRP $429.95

ps_IMG_1718

This lower comes assembled with our DMR Trigger and Ambidextrous selector. The magazine catch is machined from billet and hard anodized. The rest of the parts are our standard mil-spec components all made in the USA. Our 5.5oz heavy 9mm buffer is installed. Mount the upper of your choice with bolt carrier group that clears through glock feed ramps, and this unit is ready to go!

MSRP $629.95

KE34 Slides Now Available

Slides for Gen 3 and Gen 4 Glock 34s are now available on our site!

KE34 Charlie

ps_img_0398

Charlie Features: Front and rear cocking serrations, aggressive contouring on the sides, bull nose on the front, weight relief cuts on the top and sides.

KE34 Delta

ps_img_0351-crop

Delta Features: Front and rear cocking serrations, aggressive contouring on the sides, bull nose on the front, weight relief cuts on the top and sides. Slots through front serrations further reduce slide mass and aid in barrel cooling.

KE 34 Echo

ps_img_0295

Echo Features: Front and rear cocking serrations, aggressive contouring on the sides, bull nose on the front, weight relief cuts on the top and sides. Slots through the slide at 3, 12, and 9 o’clock to reduce mass.

Internals for Slides

glock slide service kit

At KE Arms we don’t do anything half way.  Not wanting to be dependent on other suppliers we have made a mold for the striker channel liner, striker spacer sleeve, and spring cups.  We have also produced the safety plunger, extractor plunger, and extractor  plunger bearing.  We also have the striker spring, extractor plunger spring, and safety plunger springs.  All components are made in the USA.  The safety plunger, extractor plunger, and extractor plunger bearing are melonite coated.  All the springs are black oxide coated.  These components are also compatible with Austrian striker fired pistols.

The best value is our Slide Service Kit that includes 2 of all the above components.

Order online here

Captured Fire Control Pins

captured-fc-pins-1
Captured Fire Control Pins are now available!  They are intended for use with our DMR trigger or other modular cassette type triggers. The Captured Fire Control Pins provide an extra measure of security to make sure they stay in your rifle.  While the DMR trigger does not require these pins, they provide peace of mind to users that run their guns hard.  The use of blue locktite on the screws is recommended.

Order online here